How to Torque Flange Bolts for Metal Gasket Integrity

Proper flange bolting requires following the specific torque sequence and value for your gasket type. Apply torque in a star pattern to ensure even clamping force, which prevents metal gasket distortion and leaks in industrial flanged joints.
- Use the correct star pattern to distribute clamping force evenly across the flange face.
- Verify torque values against the gasket material and flange class, not just the bolt size.
- Check gasket seating before tightening to prevent edge compression and permanent deformation.
- Re-torque bolts after initial pressure cycling to maintain a consistent seal over time.
Why Flange Bolting Sequence Matters
A metal gasket is not a passive spacer. It compresses under load to fill the micro-irregularities between flange surfaces. If you apply torque to flange bolts incorrectly, the gasket compresses unevenly. One side of the joint stays open while the other side crushes the material. This creates a leak path that no amount of over-tightening can fix.
Metal gaskets, such as spiral wrap or ring types, have specific load requirements. They need enough force to deform plastically into the flange seats but not so much force that they crack or shear. The procedure for flange bolting must match the gasket design. A standard bolt size does not guarantee a correct seal. You need the right torque specs and the right sequence.
Prerequisites Before Starting
Before you pick up a wrench, confirm three things. First, identify the flange class and the gasket type. A Class 150 flange with a graphite spiral wrap gasket requires different handling than a Class 300 flange with a stainless steel ring gasket. Second, inspect the flange faces. Look for nicks, corrosion, or flat spots. A damaged face will not seal, regardless of the torque you apply. Third, check the bolts. Reused bolts can stretch and lose tension. If the bolts have been in service for a long time, replace them.
You also need the right tools. A calibrated torque wrench is non-negotiable. A standard wrench or a power tool without a torque limit will overshoot the setting. For high-pressure flanges, you may need a torque multiplier. This tool allows you to apply high torque without straining your arm or losing control of the wrench.
Step-by-Step Flange Bolting Procedure
Follow these steps in order. Skipping the seating check or the re-torque step is the most common cause of field failures.
-
Clean the Flange Faces
Wipe both flange surfaces with a clean cloth. Remove old gasket residue, paint, or grease. Even a thin film of oil prevents the gasket from seating properly. This step is simple but often skipped. If the gasket does not sit flat, the seal fails immediately. -
Seat the Gasket
Place the gasket on the flange face. For spiral wrap gaskets, orient the wrap correctly. The outer wrap usually sits against the flange face. Do not force the gasket. If it does not drop into place, the flange face may be damaged. A metal gasket should sit flush with the flange surface. -
Hand-Tighten All Bolts
Thread every bolt by hand. Do not use a wrench yet. This ensures the gasket is not pinched or twisted. If one bolt will not thread, stop. Forcing a bolt can shift the gasket off-center. A misaligned gasket creates a high-stress point that leads to cracking. -
Apply the Star Pattern
Begin tightening in a star or cross pattern. This is not a random sequence. You tighten bolts in a way that mimics a star shape, moving from one side of the flange to the opposite side. This distributes the clamping force evenly. If you tighten in a circle, the flange will bow on one side. The gasket will compress on one edge and stay open on the other. -
Apply the First Torque Pass
Tighten each bolt to the specified torque value. For metal gaskets, this value is often lower than the maximum bolt tension. Check the gasket manufacturer data for the recommended torque specs. Do not guess. Over-tightening a graphite gasket can crush the filler material and cause it to extrude into the pipe bore. -
Check Gasket Alignment
After the first pass, stop and look at the gasket. Is it still centered? Is it compressed evenly? If one side is pushed out further than the other, the flange faces are not parallel. You may need to clean the faces again or adjust the bolt sequence. This is a critical check that most technicians skip. -
Apply the Second Torque Pass
Once the gasket is seated and aligned, increase the torque. Go back to the star pattern. Tighten each bolt to the final torque specification. This second pass ensures the gasket is fully compressed and the flange faces are pressed together. -
Verify Bolt Tension
After the final torque, check the bolts again. Use a torque wrench to verify each bolt is at the specified value. If you find a bolt that is loose, re-tighten it. If a bolt is significantly over-torqued, it may have damaged the gasket. In that case, you may need to replace the gasket.
Common Mistakes in Flange Bolting
Tightening in a Circle
This is the most frequent error. It creates an uneven load distribution. The flange face deforms, and the gasket does not seal. Always use a star pattern.
Using the Wrong Torque Value
Bolt size does not equal gasket torque. A 1/2 inch bolt on a Class 150 flange may require a different torque than a 1/2 inch bolt on a Class 300 flange. The flange class determines the pressure rating and the required clamping force. Always use the torque specs from the flange and gasket manufacturer data.
Skipping the Re-Torque Step
Metal gaskets settle during the first pressure cycle. The flange faces and the gasket compress slightly. This can reduce the bolt tension. A re-torque check after the system has been pressurized once helps restore the seal. This step is especially critical for high-temperature service.
Ignoring Flange Condition
A gasket cannot compensate for a damaged flange. If the flange face has deep grooves or is heavily corroded, no amount of torque will create a seal. You may need to lap the face or replace the flange.
Verification and Maintenance
After installation, the joint must be verified. A visual check for leaks is a start. For critical applications, use a dye penetrant test or an ultrasonic thickness gauge. These methods confirm the seal integrity without relying on guesswork.
During operation, monitor the flange bolts. If you notice a leak, do not simply tighten the bolts more. A leak means the gasket is failing or the flange is moving. Stop the service. Disassemble the joint. Inspect the gasket. If the gasket is crushed or cracked, replace it. If the flange face is damaged, machine it. Re-torquing a failed joint will not fix the root cause.
Quick Reference Table
| Flange Class | Gasket Type | Torque Approach | Key Check |
|---|---|---|---|
| Class 150 | Spiral Wrap Graphite | Moderate, star pattern | Gasket alignment after first pass |
| Class 300 | Stainless Steel Ring | High, star pattern | Flange face parallelism |
| Class 600 | Double-Wrap Spiral | High, star pattern | Bolt stretch and gasket compression |
| Class 900 | Graphite Ring | Very High, star pattern | Flange face integrity and bolt condition |
Final Verification Step
The final verification step is a pressure test. Once the flange is bolted and the gasket is seated, pressurize the line to the test pressure. This is usually 1.25 times the design pressure. Hold the pressure for a specified time. Watch for leaks. If you see no leaks, the flange bolting procedure was correct. If you see a leak, open the flange. Do not guess. Find the cause. A successful flange joint is the result of a deliberate process, not a series of random wrench turns.
Troubleshooting and Next Steps
If you are dealing with a high-pressure flange and the seal fails repeatedly, the issue may be more than just torque. Check the gasket material. A graphite gasket may not handle the thermal cycling of your application. A metal gasket may be too rigid for a flange that flexes. You may need to change the gasket type. You may need to change the bolt material. You may need to change the flange face finish. These decisions require a deeper look at the service conditions. The torque specs and flange bolting sequence are the starting point, not the entire solution.
Frequently asked questions
What is the standard torque for flange bolts?
There is no single standard. Torque depends on the bolt size, flange class, and gasket material. Always use the specific torque specs provided by the gasket manufacturer.
Can I use a power tool to tighten flange bolts?
You can use a power tool with a torque limit or a torque multiplier. Never use a power tool without a limit. It will overshoot the torque and crush the gasket.
How do I know if a gasket is seated properly?
Check the gasket alignment after the first torque pass. It should sit flush with the flange face. If one side is pushed out further, the flange faces are not parallel.
Do I need to re-torque bolts after installation?
Yes. Re-torque after the first pressure cycle. The gasket and flange will settle, and the bolt tension will drop. A re-torque check restores the seal.
What if the flange face is damaged?
A gasket cannot seal a damaged flange. You must clean the face, lap it, or replace the flange. Torquing a damaged flange will not fix the leak.


